How to Mount Art to Cover Hidden Recessed Storage

In this video I'll be showing y'all how I tore into a wall to create a built in cubby. I did this project in my bathroom merely the aforementioned steps can exist taken in any wall in guild to create a beautiful storage spot. Lets go started.

Things I Used in This Project:

• ISOtunes Ear Protection: http://bit.ly/2YuZBtr https://bit.ly/2Cf6OXP
• Stud finder: http://amzn.to/2v2c1cu
• Triton Multi Tool: https://amzn.to/3qgwNBw
• DAP Weldwood Mucilage: https://amzn.to/2JTRHqk
• Miter Saw Station: http://bit.ly/2pwceVy
• Table Saw Push Stick Caddy: http://bit.ly/343nTgf
• 16 Estimate Nailer: https://thd.co/2TcZWgX

The first thing to annotation is this wall I'grand using is not load bearing. It's but a partition wall betwixt the bathtub and the toilet. As well since the shower is separate, I figured there was no plumbing above the tub that would be in my way. Other than a vent tube which I'll get into later. All that to say: I recommend doing this project in a infinite that looks like the inside will be relatively empty.

To get started, I first figured out where I wanted the cubby to exist. I used a level to draw some lines that would put it in line with the floating shelves I congenital in my concluding video. Then I used a stud finder to locate the studs in the wall.

The easiest matter to practise would be to build a vertical cabinet in betwixt the studs and never take to affect them. All the same, I wasn't a fan of that system…I actually wanted something horizontal. The only problem with that is that means I would have to cut into the studs. In my situation this isn't a problem because this wall isn't load bearing, so I marched forward with my plan.

With the placement laid out, I next cutting into the drywall, which is an intimidating step to showtime.

I grabbed non only a shop vac but also my ISOtunes as this is a very noise step, especially in a pocket-size space. They actually brand a drywall saw that you can use for this stride but since I accept a multi tool, I went with that. It volition drastically sped upward the procedure. I would go over my pencil mark and score a line, but to first establish where the cut needed to be. So that next I could make another pass but deepen it until I felt the blade punch through the back.

To continue the grit down you tin see that I just dragged the shop vac along with my cut. Once it was cut all the manner through on all sides, I cut the top right corner out and so that I could create some sort of hand hold for pulling the piece out.

It was here I realized my fault….this cutting was the finished cubby size I wanted, but in the next step I'll take to add together 2x4s to both the top and lesser which is shrink my hole past 3". To fix this, I simply cutting back 1 1/ii" from the tiptop and bottom. If y'all do this projection, figure out your wanted finish size, then add together 1 1/2" to both ends earlier making your cubby cut. : )

This side by side step you'll be able to completely skip if you're not working effectually a tub, only let me explain this PVC pipe in my wall. This is something chosen a vent tube which is just an empty PVC pipe that goes up to the attic, connects to the other plumbing vent tubes in the business firm then goes upwards to the roof. It's sole purpose is to allow air into the system so plumbing can drain. I was hoping it would exist tucked off to the right but since it's right in my way, I had to either reroute it, or shorten it. I decided to shorten it.

To still continue information technology'southward function, I cut this pipe shorter then used a special cap called an Air Remittence valve which can exist placed anywhere in the system and will still permit air into the plumbing and then things are able to bleed.

And so I went up to the attic, find this one particular line and capped it off then no moisture would fall into my division wall here.

I didn't have enough room on the front to work in this valve and then I cut a small access on the behind to practise this work. Later attaching the valve, I placed a grate on the toilet side and then it could be accessed afterwards, then carried on the tub side with my project.

With the plumbing removed, adjacent I worked on cutting the studs out. I used a combination of a sawzall with a brusque blade on information technology, and a multi tool. Offset a sawzall to cut through the bulk of the stud, aiming to go along my tool and blade level with the drywall cut here. So a multi tool to finish off the back 10% of the cut without getting into the drywall on the other side. Information technology's a fiddling fleck of a pain considering of the screws going in from the drywall on the other side, but it piece of work eventually.

Next I cutting some 2x4s to length and fastened them to the studs in the wall. This is where I'm sure I'thousand going to get complaints. If this were a load begetting wall, I would take built a truthful header to go from the far left stud to the far right on both the summit and bottom, but since I know the framing of my house, I knew that wasn't needed.

Instead, I just needed to stabilize the studs and connect them so they wouldn't be loose and floating around in the walls, which these boards do. If you lot're wondering, they don't extend all the mode to the left stud because information technology was another 13' inside the drywall and I couldn't access it with a drill.

Ok, with that framed out, now it was time to head to the shop and start building the cubby that volition fit inside it.

I built this from the aforementioned Maple I built the floating shelves from and I started off by ripping all my needed boards at the tabular array saw, then cutting them to length at the miter. The aim here is to build something that will sit inside the 2x4s of the walls then add trim to cover up the drywall.

I recommend figuring out your dimension and so taking off 1/4" to ensure it fits nice and easy. For case, my dry wall opening was 32 1/2" long, but I fabricated my cabinet 32 one/4". Then the same on the pinnacle. You can make it a piddling minor to ensure it goes in smoothly then heart it up with shims.

Actually, before putting it in, I needed to add the back! Yous can go with any material of your pick here but I cut upward some masonite strips in my shop so used a router to bevel both edges. This mode after painting and attaching to the backside of the chiffonier, it looks like paneling which just gives the cubby some texture.

At present once I put it in place, it's bottom is resting on the 2×4 on the lesser and I'll screw it directly down to that one time I like information technology's left to right position. After getting the bottom secure, I as well put in two screws on the height, making sure to button the cabinet in equally I was doing so.

And just like that I'yard done. For finishing touches, I applied a bead of caulk around the trim then did some bear on upwardly pigment just honestly this is a pretty quick and painless project that completely enhances this space. It not only helps terminate out this unabridged infinite equally far as looks go, just gives it some function as I at present have a spot to store containers of items instead of them clogging upwardly the perimeter of my tub.

I personally love it! And now seeing how simple information technology was, I'm already looking at unlike areas in my house that could utilise a cubby just like information technology. If this is on your to do listing then I promise my feel has given yous an idea on what you tin can expect.

I'll run across you on my side by side projection.

If yous haven't already, don't forget to sign up at the elevation of this page for my newsletter so you don't miss new projects!

(Most of the links listed in a higher place are affiliate links. As an Amazon Associate I earn from qualifying purchases. Thanks for supporting me in this way.)

palmatierstriging.blogspot.com

Source: https://wilkerdos.com/2021/01/hidden-storage-turn-your-wall-into-a-cabinet-easy-diy

Share this post